Arduino Store

Call To +919778245216

Shopping Cart

close

No products in the cart.

Return to shop

Arduino Store

Shopping Cart

close

No products in the cart.

Return to shop

Category: SERVO MOTOR

SERVO MOTOR

Showing all 9 results

  • Sale!

    DESCRIPTION
    This is a digital servo motor for a wide range of applications which requires high torque. Metal gears ensure long life and torque conversion.

    Read more
  • Sale!

    DESCRIPTION
    This GS-5515BB High torque standard analog servo, metal brush motor, metal gear, dual ball bearing, JR connector. Mainly used in robotics and DIY projects. Buy best quality servo motors from us and get more exciting offers

    Read more
  • Sale!

    DESCRIPTION
    The 10kg.cm Metal Gear Servo Motor – MG995 can rotate approximately 120 degrees (60 in each direction). You can use any servo code, hardware or library to control these servos, so it’s great for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. The MG995 Metal Gear Servo also comes with a selection of arms and hardware to get you set up nice and fast!MG995 is a digital metal gear high torque servo for airplane, helicopter, RC-cars from 10 to 6-th scale truggy and monster and many RC model.

    Read more
  • Sale!

    DESCRIPTION

    Add more power to your robot with this metal-geared MG90S servo. The tiny little servo can rotate approximately 90 degrees (45 in each direction), and works just like the standard kinds you’re used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gearbox, especially since it will fit in small places. Of course, its not nearly as strong as a standard servo. Works great with the Motor Shield for Arduino, our 16-channel Servo Driver, or by just wiring up with the Servo library. Comes with a few horns and hardware.

    Read more
  • Sale!

    These TowerPro MG995 – Continuous Rotation 360° Metal Gear Servo Motor are high-speed servo motors with a mighty torque of 9.4 kg/cm. It has metal gears which makes it robust and reliable motors.

    Read more
  • Sale!

    DESCRIPTION
    MG996R is an upgraded version of MG995 servo. The new PCB and IC control system which makes it far more accurate. Its internal gearing and motor are also upgraded to improve dead bandwidth and centering. It is a great choice for 1/10 buggy and airplane helicopter, RC-cars from 10 to 6-th scale truggy and monster and many RC model.

    Read more
  • Sale!

    Description
    This is the Futaba S3003 Standard Servo.
    This basic servo is used in cars, boats, or where standard servos are used.
    This is the replacement for the following servos, S138,S148,S22,S38 and S12.
    This servo can produce high-current draw from your batteries.
    If using NiMH or LiPo batteries, make sure they are capable
    of delivering sufficient amps.

    Read more
  • Sale!

    DESCRIPTION
    Servo Motor Tester ESC Consistency CCPM Controller can be used as a signal generator for electric speed controller (ESC), then you can test your motor system without using a transmitter and receiver. There are 3 modes to check servos or ESC: —Manual mode: turn the knob with different speed, check the reaction time. —Neutral mode: make the servo go back to the neutral point. —Automatic / window wiper/ mode: make the servo swing like a window wipers in the biggest angle.

    It can connect 1-3 servos simultaneously and test such as 1-3 servos consistency and so on.You can also connect 1-3 ESC to test and compare their reaction time respectively. It can connect 3 servos of the CCPM helicopters and select servos. It can also connect the servo of airplanes install the steering-box and adjust planes by using such as the neutral mode and so on.

    Read more
  • DESCRIPTION
    It is tiny and lightweight with high output power. This servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds but smaller. You can use any servo code, hardware or library to control these servos.It comes with a 3 horns (arms) and hardware.

    Read more